Make Your Own Eyeglasses Case – Simple DIY Project

We are here today with another easy sewing tutorial for you guys that makes a great gift, an eyeglasses case. You’ll definitely want to pin this one for a few weeks from now when you’re frantically searching for an easy handmade stocking stuffer!




 
 
In my opinion, the best handmade gift is one that will be used often, so this DIY eyeglasses case is a perfect choice. Read below for simple instructions on how to make your own.

glasses-sleeve-tutorial
 
MATERIALS NEEDED:

– For the front you can use any woven fabric, leather, or faux suede. I used a linen/cotton blend by Anna Maria Horner for the front. Choose fabric with structure and body, or add interfacing to fabric that is lighter weight.

– For the inside I like to use something soft to protect the glasses. For these cases, I used a performance fabric by Roc-lon® called Mardi Gras 2 Roc-Suede. It’s technically a black out fabric for household use, but it’s like a faux suede and perfect for protecting glasses. The coating on the back acts like interfacing and adds structure to the cases.

Interfacing: If neither your outer or inside fabric have much structure, fuse a piece of interfacing to your outer piece. Cut your piece of interfacing 2.5cm smaller than the outer fabric on both the width and height. (If your outer fabric is 19cm by 19cm, but the interfacing piece 16cm by 16cm).
 
STEP BY STEP INSTRUCTIONS:

Cut two pieces of fabric, one for the inside and one for the outside, measuring 7.5 inches tall by 7 inches wide.

DSC01030

Place the two pieces together with right sides facing.

DSC01036

Fold them together lengthwise, keeping the fold on the left side. Use a glass cup or other round object to trace a curved corner on the bottom right. (Remember, this should be on the side with the raw edge, not the folded edge).

DSC01037

DSC01038




 
 
Use a sharp pair of scissors to cut along the curve. I tried using a rotary cutter for this step but it’s tricky to cut a small curve, even with a small rotary cutter.

DSC01042

Open your pieces up and pin them together on all four sides, with right sides facing.

DSC01049

If you are using leather, which shifts A LOT under the sewing machine presser foot, use these clips to hold the layers in place. Don’t use pins in leather, because they will leave visible punctures in the leather.

DSC01048

Sew around your fabric on all four sides with a 1cm seam allowance. Leave a 7cm gap along the top so you can turn your fabric right side out. As you can see below, the curves are difficult to sew neatly. Go slow and keep your eye on the edge of your fabric, rather than the needle. If your corners get wonky (like mine!), go back over them with the sewing machine and even out the curve.

DSC01057

My corners looked much better when I went back and fixed them. For a cleaner curve, you can also trace the corner with a pencil or pen and use the line as a guide for your stitches.

DSC01062

Again, make sure you left a 3″ gap in the top edge so you can turn the fabric right side out after the next step. (As you can tell by my photo, I forgot to sew along the top edge originally, and had to go back and add this seam. Oops! Do as I say and not as I do).

DSC01069

Trim your seam allowances to 0.5cm along all four sides, being very careful not to cut into any stitches.

DSC01063

Clip the rounded corners. This will make the curve smooth when you turn it right side out and press.

DSC01076

Pull the fabric right side out through the opening.

DSC01080

Tuck the opening under 0.5cm and press well on all four sides.

DSC01086

DSC01089

Make sure the rounded edges are nicely pressed.

DSC01093

Pin the opening closed along the top edge, making sure the seam allowance is pressed under and even 0.5cm.

DSC01094

Top stitch along the top edge, starting at one corner and backstitching at the other end. Your stitches should be about 0.2cm from the edge. This will secure the opening closed and add a nice finishing touch to your glasses case.

DSC01098

Fold your glasses case so that the outer fabric faces out. Carefully match the curved edges and pin well.

DSC01110

Back at the sewing machine, stitch the side and bottom edge 1/8″ from the edge. Then go back and add a second row of stitches 0.2cm from the edge. This will give you two nice rows of topstitching and add strength to the seam.

DSC01113

roses-glasses-case

Tada: a beautiful eyeglasses case for your own use, or for a friend! These come together in about 15 minutes, which means they are great last-minute gifts for birthdays or Christmas. Throw them in stockings, hang them on the tree, or fill them with candy and use them as holiday dinner favors. Imagine the possibilities!

rose-glasses-case2

I think it would be fun to extend the height by about 1cm and add a button closure to the top, or embellish with embroidery. I even made the eyeglasses case pictured below to go with the travel bag I made my husband last Christmas:

handmade-gifts-for-men
pink-glasses-case2

The eyeglasses case pictured below features Roc-Lon faux suede on the outside and quilting cotton on the inside, a reverse of the case I made for this tutorial.

purple-suede-glasses-case

Related posts:

Easy DIY Minions Bento Box – Your Kids Will Love it – (VIDEO)

DIY: Make A Cheap Pizza Oven Using A Fire Pit And A Flower Pot

Beautiful knitted hanging planter – perfect for your balcony

How to make amazing seating from your old tyres

Make cute candlesticks from your old wine glasses

Source: www.hideousdreadfulstinky.com

Leave a Reply

Your email address will not be published. Required fields are marked *